Redmoon Converters 精确计算所需油漆量：墙面面积减去门窗面积后，乘以涂刷遍数和底漆，并考虑表面质地覆盖系数及各品牌的m²/L覆盖率。
| 名称 | 长 | 宽 | 高度 | 门 | 窗 |
|---|
| 房间 | 墙面面积 | 净面积 |
|---|
每个房间的墙面面积： 2 × (长 + 宽) × 高度。可选择加上天花板面积 = 长 × 宽。
减去门窗面积： 每扇门 21 平方英尺，每扇窗 15 平方英尺（约 1.95 m² 和 1.4 m²）。
所需油漆量： 总净面积 × 涂刷层数 / 每加仑覆盖面积。覆盖面积取决于表面质感：光滑面 350，轻质感 300，重质感 250 平方英尺/加仑。
底漆： 所有表面涂刷一层，约 200 平方英尺/加仑。始终向上取整为整数容器。
The calculator works room by room. For each row it takes wall area as 2 × (length + width) × height, optionally adds length × width for the ceiling, then subtracts a flat 21 square feet per door and 15 square feet per window to get net paintable area. Totals across all rooms are multiplied by your coat count and divided by the coverage rate, and the answer is rounded up to whole containers, because you cannot buy two-thirds of a tin.
Surface texture is the coverage rate, and it is the biggest single lever: Smooth gives 350 sqft/gal, Light texture 300 and Heavy texture 250, so a heavily textured wall needs 40 percent more paint than a smooth one for the same area. Coats defaults to 2 and accepts 1 to 5. Turning Primer on adds a separate single coat costed at 200 sqft/gal, reported alongside the topcoat figure rather than mixed into it.
The opening deductions are fixed averages, not measurements: every door counts as 21 sqft and every window as 15 sqft regardless of the real size or the unit system you selected. Trim, doors themselves, closets and soffits are not counted. Metric mode computes in square feet and gallons internally and converts at 3.78541, then rounds to whole litres — which will not line up with the 2.5 and 5 litre tins actually sold, so round to real tin sizes yourself.
With 8 foot ceilings that is 384 sqft of wall. Deduct one door and one window and you get 348 sqft net; two coats at the smooth 350 sqft/gal rate works out to 1.99 gallons, which the tool rounds up to 2 gallons.
No. Each room row has Doors and Windows count fields. Enter how many of each and the tool removes 21 sqft per door and 15 sqft per window automatically. If a room has an oversized picture window, enter it as two windows to approximate the area.
Only if you set Include ceiling to Yes, which adds length × width to every room's area. It is off by default, and it uses the same texture coverage rate as the walls, so adjust the texture setting if your ceiling is a different finish.
Keep coats at 2 and switch Primer on. Primer is costed separately as one coat at 200 sqft/gal, which is the standard approach for going dark to light, over patched drywall, or onto bare or glossy surfaces where topcoat alone will not sit evenly.
Because the result is rounded up to whole containers. Adding a few square feet can push 1.98 gallons to 2.01 and force a third tin. The per-room table below the result shows the underlying gross and net areas so you can see what actually moved.
Concrete Volume & Bags Calculator
Cubic yards / metres of concrete needed for slabs, footings, columns and posts, plus bags-of-mix conversion.
Lumber Board Feet & Cost Calculator
Calculate board feet, linear feet and total cost for hardwood and softwood lumber.
Tile & Flooring Coverage Calculator
Tiles or boxes needed for any floor or wall area, with pattern waste and grout lines.
BTU & HVAC Sizing Calculator
BTUs needed to heat or cool a room from area, ceiling height, insulation, climate and sun exposure.
MIG Welding Settings Calculator (Amps, Volts, Wire Speed)
Recommended MIG welding voltage, amperage and wire feed speed by metal thickness, wire diameter and material.
Landscaping Material Calculator (Gravel, Mulch, Soil, Sand)
Cubic yards, weight, bags and cost of gravel, mulch, topsoil or sand needed for any area and depth.